Bionaire BAOF25M Bedienungsanleitung PDF herunterladen

mounting nut. Turn this nut clockwise and tighten

firmly.

4. Remove the protective sleeve from the motor shaft.

5. Slide the fan blade (J), with the fixing screw facing

towards the rear grill, firmly onto the motor shaft,

aligning the screw with the flat (K) on the motor shaft.

6. Position the locking screw (L) over the flat on the

motor shaft. Tighten the screw into the side hole of

the fan blade, against the motor

7. Loosely fit the grill ring (M) to the front grill (N). Position

the fixing screw (O) at the bottom of the grill with

reference to the Bionaire logo

™

. The grill ring has two

grooves. Locate the front grill to one of these grooves

leaving the other groove free to attach to the rear grill.

Only tighten the fixing screw enough to hold the grill

ring in place.

8. Center the front grill by aligning the Bionaire logo

™

the logo plate so that it is horizontal and parallel with

the floor. Then, holding the front grill against the rear

grill, push the black grill ring into place at the top and

bottom of the fan. (Push directly on the black grill ring,

not on the grills themselves). Finish securing the grill

ring in the same manner until both grills are joined

underneath the black ring.

9. Tighten the screw.

OPERATING INSTRUCTIONS

1. Set the fan base on a dry level surface.

2. Make sure the Speed Control is in the OFF (0)

position. Speed Control (P) is located on the top of

the fan motor housing.

3. Plug the cord into a suitable outlet.

4. The SPEED is adjusted by turning the Speed Control

to the desired setting:

0 - Off

I - Low

II - Med

III - High

ADJUSTMENT INSTRUCTIONS

Tilt adjustment

Follow these instructions to tilt the fan head for upward

angle air movement.

• To change the tilt angle of the fan head, simply move

the fan head to the desired angle.

Oscillation adjustment

The OSCILLATION control (Q) is located on the top of the

fan motor housing. To start oscillation, push the control

knob down. To stop oscillation, pull the control knob up.

FAN SAFETY

PLEASE READ AND SAVE

THESE IMPORTANT

SAFEGUARDS

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic safety precautions

should always be taken including the following:

1. Read all instructions before using this appliance.

2. Use fan only for purposes described in the instruction

manual.

3. To protect against electrical shock do not immerse

unit, plug or cord in water or spray with liquids and

plug the appliance directly into a electrical outlet.

4. Close supervision is necessary when any appliance is

used by or near children.

5. Unplug from outlet when not in use, when moving fan

from one location to another, before putting on or

taking off parts and before cleaning.

6. Avoid contact with moving parts.

7. Do not operate in the presence of explosive and/or

flammable fumes.

8. To avoid fire hazard, NEVER place the cord under

rugs or any parts near an open flame, cooking or

other heating appliance.

9. Do not operate any appliance with a damaged cord or

plug after the appliance malfunctions, or has been

dropped/damaged in any manner. Take it to an

Authorized Service Center for examination and/or

repair.

10.The use of attachments not recommended or sold by

the appliance manufacturer may cause hazards.

11.Do not use outdoors.

12.Do not let the cord hang over the edge of a table,

counter or come in contact with hot surfaces or leave

exposed to high traffic areas.

13.To disconnect, grip plug and pull from wall outlet.

Never yank on cord.

14.Always use on a dry, level surface.

15.Do not operate fan until fully assembled with all parts

properly in place.

16.This product is intended for household use ONLY and

not for commercial or industrial applications.

17.WARNING: To reduce the risk of electrical shock and

injury to persons, do not use in window.

18.WARNING: To reduce the risk of fire or electric

shock, DO NOT use this fan with any solid-state

speed control device.

PLEASE SAVE THESE

INSTRUCTIONS

ASSEMBLY INSTRUCTIONS (SEE FIG. 1)

1. Fit the upper body (A) to the base (B). Align the 4

screw holes in the base to the four holes in the upper

body. Fix securely with the 4 sets of screw, spring

washer and flat washer (C).

2. Unscrew the rear grill mounting nut (D) from the motor

housing (E). Position the rear grill (F) over the motor

shaft (G), making certain 2 notches (H) at the sides of

the rear grill fit over the corresponding prongs (I) on

the motor housing. Please make sure the rear grill fits

securely against the motor housing.

3. Secure the rear grill in its place using the rear grill

CLEANING/MAINTENANCE INSTRUCTIONS

Follow these instructions to correctly and safely care for

your fan.

• Always unplug the fan before cleaning or

disassembling.

• Be sure to clean your fan with a soft cloth moistened

with a mild soap solution.

• Do not allow water to drip on or enter into the fan

housing.

• Do not use gasoline, thinner, or benzene as a cleaner.

•Lightly run a vacuum cleaner nozzle over the fan grill

to remove any dust or dirt that may have

accumulated.

Fan Blade Cleaning Instructions

Make sure the fan is unplugged before disassembling and

cleaning the fan blade. Carefully remove the front grill from

the clips. Wipe the blade with a soft cloth moistened with a

mild soap solution. DO NOT allow any liquid to drip into or

enter the motor housing. Snap the front grill onto the fan.

Make sure all parts are secured prior to operating the fan.

FAN STORAGE

Your fan should be stored in the off-season in its original

box. It is important to keep it in a safe, dry location.

• Store your fan in the original box or an appropriately

sized box.

•Protect the fan head from dust.

How To Obtain Warranty Service: Please see the

country specific warranty insert or contact your local

authorized distributor for Bionaire appliances.

PLEASE DO NOT RETURN THIS PRODUCT TO THE

PLACE OF PURCHASE

Distributed by Sunbeam Products, Inc., doing business as

Jarden Consumer Solutions, Boca Raton, Florida 33431.

One year limited warranty - please see inside for details.

RETRO TABLE fan

BAOF25M

Read instructions before operating.

Retain for future reference.

Instruction Leaflet

A. Upper Body

B. Base

C. Screw/ Spring Washer

/ Flat Washer (4)

D. Mounting Nut

E. Motor Housing

F. Rear Grill

G. Motor Shaft

H. Notches

I. Prong

J. Fan Blade

K. Flat

L. Locking Screw

M. Grill Ring

N. Front Grill

O. Fixing Screw

P. Speed Control

Q. Oscillation Control

Figure 1

BAOF25MLA06ESM3.qxd 10/25/06 18:56 Page 1

1 2

RETRO TABLE fan 1
VENTILADOR retro 2

Inhaltsverzeichnis

Seite 1 - RETRO TABLE fan

mounting nut. Turn this nut clockwise and tightenfirmly. 4. Remove the protective sleeve from the motor shaft.5. Slide the fan blade (J), with the fix

Seite 2 - VENTILADOR retro

SEGURIDAD DEL VENTILADORLEA Y GUARDE ESTAS IMPORTANTES MEDIDAS PREVENTIVASINSTRUCCIONES IMPORTANTESAl utilizar electrodomésticos, siempre se deben tom

Kommentare zu diesen Handbüchern

Keine Kommentare

Bionaire BAOF25M Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Telefone Bionaire BAOF25M herunter. BAOF25M - Bionaire Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern